Metering units
AGZU in standard execution

Measuring installations "Sputnik-Massometer NT.1" (hereinafter referred to as installations) are designed to measure the mass and mass flow rate of borehole fluid (crude oil) as part of an oil and gas mixture, the mass and mass flow rate of crude oil excluding water (oil), measurements of the volume and volume flow rate of free petroleum gas, reduced to standard conditions.

Learn more

AGZU small-sized installation

Measuring installations "Sputnik-Massometer NT.1" (hereinafter referred to as installations) are designed to measure the mass and mass flow rate of borehole fluid (crude oil) as part of an oil and gas mixture, the mass and mass flow rate of crude oil excluding water (oil), measurements of the volume and volume flow rate of free petroleum gas, reduced to standard conditions.

Learn more

AGZU mobile installation

Measuring installations "Sputnik-Massometer NT.1" (hereinafter referred to as installations) are designed to measure the mass and mass flow rate of borehole fluid (crude oil) as part of an oil and gas mixture, the mass and mass flow rate of crude oil excluding water (oil), measurements of the volume and volume flow rate of free petroleum gas, reduced to standard conditions.

Learn more

Spare parts for metering unit AGZU
Pressure control device (URPD)

The differential pressure control device is designed to operate in a level control system and the pressure drop in group measuring installations of the Sputnik type for installation instead of conventional gas dampers of the CE, ZG, PDRK, eccentric type.

Learn more

Magnetic control valve (KMR)

Magnetically controlled valves are designed to operate in the fluid flow control system in Group Measuring Units of the "Satellite" type for installation instead of conventional flow regulators of the PP type.

Learn more

Multi-stream switching manifold (PSM-4-NT)

The switches are installed on automated group-measuring installations of the "Satellite" type, and are designed for manual and automatic installation of wells for measurement.

Learn more

Hydraulic drive (GP-NT)

Designed to create hydraulic pressure in the power hydraulic cylinder of the multi-pass well switch (PSM).

Learn more

Sliding gate valve with hydraulic drive (SHZ-GP)

The device is designed for periodic short-term opening of the passage of liquid (gas) in the pipeline, as well as for creating a pressure drop between the measuring separator and the common collector of the automated measuring installation (AGZU) "Satellite".

Learn more

Devices for well dewaxing
Tubing cleaning device (UOK)

«Устройство для очистки колонны насосно-компрессорных труб (НКТ) нефтяных скважин от парафина типа УОК-НКТ» предназначено для непрерывной очистки всей внутренней поверхности колонны НКТ путем срезания слоя парафина со стенок.

Learn more

Lubricator platform PL-3.0

The PL-type lubricator site is designed for the safe conduct of geophysical work on a well, the mouth of which is equipped with a lubricator installation..

Learn more

Flow meters
Flowmeter - ERVIP.NT

ERWIP explosion-proof flowmeters.NT-Vn represents flowmeters of general industrial execution in the execution case "explosion-proof shell" "d", made in accordance with the requirements for explosion-proof electrical equipment of subgroups IIB, IIA according to GOST R IEC 60079-14.

Learn more

Turbine TOR.NT liquid meter
Designed to measure the amount of liquid (water, oil and petroleum products) in units of volume at technological installations of oil and gas producing enterprises and other sectors of the national economy.

Learn more

Reagent deodorization devices
UZP-NT

Devices of chambers for launching and receiving in-line means for KVS pipelines are designed for periodic launching into the pipeline and receiving from it in-line projectiles-flaw detectors, cleaning scrapers and other in-line means.

Learn more

Pig launcher-receiver for gas pipelines UKZ&P-NT

The chambers for launching and receiving in-line cleaning and diagnostics of KVS are designed for periodic launching into the pipeline and receiving from it in-line projectiles, flaw detectors, cleaning scrapers and other in-line means.

Learn more

Valve manifold (BG-NT)
The comb block is designed to distribute, change the flow rate and pressure of process water injected into injection wells of the reservoir pressure maintenance system.

Learn more

Chemical injection block (BDR-NT)
Chemical injection block (BDR-NT)
The reagent block is designed for metered injection of liquid demulsifiers and corrosion inhibitors into the pipeline of the oil transportation and treatment system in order to carry out in-line demulsification of oil, as well as protection of pipelines and equipment from corrosion, paraffin deposits, etc.

Learn more